Sharpening Machinery / Sawmill Machinery

2 Akemat B4 Automatic Saw Blade Face Grinder ( 1996 / 1997)

Saw blade diameter capacity 70-800 mm (2.7"-31.4")
Tooth kerf up to 20 mm (0.78")
Tooth pitch 8-125mm (0.31"-4.92")
Rake angle -10 degree up to +30 degree
Infinitely variable grinding speed
Cycle time up to 15 teeth per min
Diamond wheel capacity 150 mm
32 mm grinding wheel bore
2.5 kw, 460 volt, three phase
Wheel surface speed 28 m/sec
30 liter coolant tank
Front automatic lift and close of safety door
Front operator inspection window
Side mounted operator controls

Akemat B-4 Saw Blade Face Grinder

Akemat U3 Automatic Top Saw Blade Grinder (1997)

Saw Blade Dia Cap: 150 - 800 mm (6" - 31.4")
Tooth kerf: up to 10 mm (0.39")
Tooth spacing: 8 mm to 80 mm (5/16" to 3 1/8"
Back clearance angle: 10 up to +30
Top bevel angle: up to 45
Infinitely variable grinding speeds
Diamond wheel cap: 150 mm
32 mm grinding wheel bore
2.5 kw, 460V, 3 ph
Front automatic lift and close of safety door
Front inspection window
Side operator controls





Akemat F3 Automatic Saw Blade Side Grinder

Double side grinder head
Automatic kerf adjustment
Automatic index system
Saw blade cap: 150 800 mm (6 31.4)
Infinitely variable grinding speeds
1.75 hp, 460V, 3 ph grinding motors
Front automatic open and close of safety guard
Front inspection window
Side operator controls





Vertical Circular Saw Leveler

Excellent Condition...Low Hours.

Simonds latest Filing Room Equipment Innovation is the Vertical Circular Saw Leveler. This compact machine is laser accurate, genuinely gravity free, fast and powerful, and provides "one touch" operation. The simple set up process of 1) load the saw, 2) press the button and then 3) remove a level, dish free saw has been sped up incredibly by the addition of Radial Rolling capability. Simonds patent pending new Ball Design allows the machine to not only roll in concentric circles, but to also attack ridges in straight lines. You�ve got to see what this machine can do!

The intuitive controls of this machine make for the simplest operation imaginable. The machine stops automatically when the work cycle is complete, you change saws, and push a single button to process the next saw. The machine automatically measures the saw diameter and processes it without any other input from the operator. If a dish condition is detected, the machine will remove it, and then work the rest of the saw for level and automatically stops when done to prevent overworking the saw plate. The VCL will roll either concentrically or radially depending on which is better and faster for the saw. Saw gauge changes are made with a simple turn of the wrist. You can load as many as four plate gauge presets for immediate access.

Levelling Action

This machine WILL automatically remove radial bumps. The key to removing radial bumps is working as close as possible to the eye. This machine has been specifically designed to work very close to the splines to get these tough bumps out. The machine comes ready to level #3 spline eye saws and can be customized to handle alternate center hole configurations and / or saws with slots and strobes as well.

The compact design of this machine belies its strength. The mass of the Simonds Vertical Circular Leveler is where it counts - in the workhead. The massive casting that does the work provides unmatched power. The machine has a small footprint and is a neat compact package designed to fit comfortably into any filing room.

Specifications:
Electrical:	460V / 3 phase, 60 Hertz, requires 15 Amp disconnect
Air:	80 lbs. Mill air (machine has F-R-L built in)
Space Required:	Overall 60" wide (including control panel arm) x 45" deep x 63" high. Actual base footprint is less than 3 foot x 3 foot.
Weight:	Approximately 1,600 lbs shipping weight
Saw Specifications:	32" diameter with #3 spline Up to .150" thick plate Can be optioned to accomadate strobe saws or saws with expansion or similar slots

Simogrit ranges from 1/4" to 1-1/2" width, gulleted and continuous, in Fine, Medium, Medium/Coarse, and Coarse grits. Offered in coil form or welded to length - call for availability.
(http://www.simondsinternational.com/productpages/eqpverticalleveler.php?menu=mnuILumbermill)

Taylor Winfield Welders

We currently have two Taylor Winfield Welders for sale. Both are in excellent working condition.

Ideal Welder
Fabrication #: 229376

This 2002 Ideal Welder is in terrific condition. If you are welding small bands, you are going to need this machine. Compact and durable, we are certain the Ideal will improve your operation.